The "I sold my NA Miata to a forum member and have some parts left over" sale.

Daikei boss for an airbag equipped NA8C with 40mm spacer (out of production). Comes with the plug & play connector to fool the airbag light. With this spacer it's ideal to mount a Nardi or Momo wheel with not much dish like a Momo Prototipo. Purchased from Rev9 Autosport, been on the car for about 100 miles. $160 including shipping to the lower 48.

Garage Star seat rails, complete with all mounting hardware. Been on the car for several months and maybe 200 miles, but are marked slightly because I was swapping seats like it was an Olympic sport. $150 shipped to the lower 48.

Hardtop brackets in good condition, $55 shipped to the lower 48.

Prices are all inclusive and assume you're paying me by Paypal. No funny business about adding fees and all that . You're welcome to pick them up locally and I'll give you a discount, obviously.

Please check back on this thread from time to time as I've got a few more parts to like (JR M45 kit for the 1.8, free OEM exhaust, R style lip etc) that I haven't managed to photograph yet.

Garagestar pic isnt working, but is this a matching pair of the side mount only rails?

If so, I think I want those.

Pic should be working now. It's the full set of rails for a single seat - so yes, there are two rails.

Oh right I forgot how much those were. A bit out of "buy these for later budget" for me.

That hub is awesome! Nice prices.

Thanks, I'm trying to be very fair with the pricing. No cheap stuff here, unfortunately .

Seat rails sold.

More bits.

JR M45 supercharger kit for a 1.8 with PS and AC - was sold to me complete, but it looks to me like the tensioner is either missing or has been disassembled until it's unrecognisable (at least to me). Comes with JR power card and MSD ignition box. Comes with a higher boost overlay for the crank pulley. You get everything that is in the pictures plus a whole lot of styrofoam peanuts.

$1250 shipped ConUS, going rate is normally higher but I want to make sure you can fit a TDR tensioner into the budget.

Next up, a set of 85.5mm Supertech pistons complete with a Cometic 85.5mm head gasket. This allows you to build the biggest displacement 1.8L Miata engine you can without stroking it. IIRC it'll bump displacement to a bit over 1.9L. The piston pictures show the one that has been unpacked and rewrapped to show that I'm not trying to sell you 3 new and one used piston . $375 shipped ConUS.

Next up, a test pipe for a 1.6L NA Miata. Only ever taken out of the box, never fitted to anything. $40 shipped ConUS.

A very shiny A-pillar gauge pod for 2x 52mm gauges. Some scratches from storage, but never used. $15 shipped.

Those hard top latches don't fit with the roll bar, right?

Correct, that's why the car has the rather expensive Beatrush latches on it.

If you're still planning to take out the rollbar, these might come in handy. I even still have the Beatrush box .

Nah, I like the bar, and I have figured out how to make the seat belts work with it ok. The aftermarket latches poke me in the shoulder occasionally though.

Deposit taken on the supercharger kit.

Set of 15x7 Rota wheels (IIRC 35mm offset) with Federal 595 RSR tires. Comes with appropriate aluminum hub centric rings and a set of BWR wheels nuts.

Please note one of the tires has had an imbalance from the factory that I haven't been able to get completely balanced out.

$350 for wheels, rings and nuts, pick up only due to the cost of shipping.

Wheels sold.

Pistons, headgasket, gauge mount, steering wheel boss and hardtop clasps are still available.

I also have a complete Mazda OEM workshop manual for a 1994 NA Miata that is now surplus to requirements. $110 picked up/$130 shipped ConUS. bgkast, if you want it I'll give you a discount.

Shop manual sold.

Your cat looks just like mine. That is strange.

We actually have two of those, they're (almost) identical twins as well.

How much for the cat?

Dang, missed this until just now

ryanty22 wrote: How much for the cat?

Not for sale, I need someone to help me turn the pages of the manuals when I'm wrenching.

I'll take the a-pillar pod

In reply to calteg:

You may or may not have a PM.

What's the lowest you'll take for the hub?

In reply to mrhappy:

That's a very good price as is, especially given that they're not making the spacer anymore. IIRC it cost me around ~250 to get it and it's only seen a few hours of use.